Frequently asked questions

Our manufacturer in Finland keeps every model in stock as standard. That means we can often deliver within a week and schedule installation and operator training straight away.

Our electric systems have low, predictable running costs, mainly electricity. Some systems also contain simple wear parts (such as filters) that are replaced periodically. No gas contracts or expensive consumables are needed.

Yes. We offer lease and financing options through specialised partners. During a demo we discuss the options and an indicative ROI calculation for your situation.

Yes. All systems are CE-certified and equipped with sensors, an emergency stop and safety protocols. Operators receive training and certification so treatments are carried out safely and responsibly.

All systems run on standard 220–230 V and require no nitrogen or special infrastructure. Rooms do need to meet normal ventilation and climate requirements (temperature and humidity), depending on the device.

You receive a 36-month factory warranty on materials and workmanship, and 12 months on computers and electronic components. On top of that we provide fast remote support and, where needed, on-site support.

On delivery we provide operator training with a certificate. Remote support and periodic refresher training are included, so your team uses the technology safely and effectively.

Gyms, sports clubs, physiotherapy practices, wellness centres, spas, beauty salons, high-end studios and home use. Together we work out which configuration best fits your target group.

No. The e°CABIN™ runs on a standard 220 V connection and needs no nitrogen tank, ventilation system or building work. We do check the electrical capacity beforehand.

Yes. If the cabin can be wheeled in as a whole (at least 90 cm door width and 205 cm height), installation is usually completed within an hour. If the passage is narrower, we temporarily take the cabin apart in three sections and reassemble it on site. The cabin is then still operational within half a day.

Allow roughly 2.5 × 2 metres of floor space and 2.5 metres of ceiling height. That fits most treatment and wellness rooms.

Yes. The e°CABIN™ is fully electric and CE-certified. Temperature and safety are continuously monitored by sensors, and sessions last only a few minutes.

One annual service check is enough. There are no gas refills or nitrogen logistics costs; only electricity. That keeps running costs low and predictable.

Installation and training take place on the same day. In most cases you can welcome clients for whole-body cryo sessions the very next day.

The e°CABIN™ uses no nitrogen or pressure vessels, so there are no refill contracts, special logistics or extra safety requirements. The experience is comfortable, the cost per session is low and temperature control is very precise.

Yes. Thanks to sensors and automatic temperature control, a user can start a session independently after instruction. That makes the cabin suitable for professional studios as well as private set-ups.

No. The X°Cryo™ runs on a standard 220 V connection and requires no nitrogen tank or special ventilation system. The treatment room does need controlled humidity.

The unit is compact (about 75 × 45 cm) and on wheels. A small corner or treatment room is enough to use the system safely and comfortably.

Yes. The X°Cryo™ is CE-certified. The temperature is continuously measured and controlled, so the skin is never exposed to cold air for too long or too intensely.

Yes. After a short instruction a treatment can be carried out independently, supervised if needed. That makes the system flexible to use in studios, wellness centres and physiotherapy practices.

The X°Cryo™ is essentially maintenance-free. In practice it comes down to regular cleaning of the applicators and periodically emptying the condensation reservoir. No refills, gases or expensive maintenance contracts are needed.

Immediately. The X°Cryo™ is fully plug & play: plug it in, a short explanation, and you can start treating.

The X°Cryo™ is fully electric, mobile and works without liquid gases. That means no gas deliveries, no nitrogen risks and a much lower cost per session — with a very powerful, controlled cold airflow.

The LedPro™ runs on 220 V / 16 A. The room must be well ventilated, with at least one metre of free space around the unit and a temperature below about 24 °C, so heat can be dissipated properly.

About 2 m² of floor space is enough. The LedPro™ has a free-standing, professional design that fits well into most treatment and wellness rooms.

Yes. LedPro™ uses scientifically studied wavelengths of red and near-infrared light and is CE-certified. The treatment is non-invasive, painless and suitable for all skin types, provided it is applied correctly and with eye protection.

Many users notice a difference in energy, recovery or skin condition after just a few sessions. The effects build up gradually with regular use, for example several times a week.

A 15-minute session uses about 0.7 kWh of electricity, roughly €0.18–€0.25 at average rates. Maintenance consists of periodic cleaning and an annual check. The LED modules last up to about 100,000 hours.

Yes. Operation is via an intuitive touchscreen with pre-programmed protocols. After a short instruction a client can start and finish a session independently.

The OxyPro™ runs fully electric on 220 V and needs no nitrogen tank or medical gas infrastructure. The room must be well ventilated, dust-free and within the recommended climate range (about 10–40 °C, humidity <80%).

The VS1 soft-shell needs about 2.5 m². The VH1–VH4 hardshells need on average 4–8 m², depending on the model. The compressor and concentrator units together take up less than 1 m² and can be placed right next to or behind the chamber.

Every OxyPro™ is delivered as a complete system, including the pressure chamber, compressor, oxygen concentrator, hoses, filters and safety valves. We also take care of on-site installation and user instruction.

Yes. The systems operate at mild pressure (approx. 1.3–1.5 ATA) and are CE-certified. All chambers have automatic pressure control, an intercom, emergency release and controlled oxygen supply. Correct use in line with the training and environmental guidelines is essential.

We position the OxyPro™, connect all components and run a full test. Operator training follows straight after. In practice installation is usually completed within half a day, and you can start sessions the same or the next day.

Electricity use is roughly 1.1 to 2.2 kWh per session, depending on model and duration. The OxyPro™ also needs simple periodic maintenance: replacing filters (about every 8–12 months), emptying condensation water and refreshing the water in the air-conditioning unit. An annual technical check is recommended.

Yes. The VS1 soft-shell can be operated fully independently from the inside. The VH hardshells can be operated both internally and externally, so as a practitioner you can keep control where needed.

The OxyPro™ is used in recovery and wellness studios, physiotherapy practices, rehabilitation centres and high-end gyms, and increasingly in private settings too. The mild pressure and comfortable interior make the therapy accessible to a broad audience.

No. The X-TONE™ runs on a standard 220 V connection and requires no special ventilation infrastructure. A normal treatment room is enough.

The unit has a compact design (about 139 × 38 × 59 cm). Roughly 1 m² of free space plus a treatment couch or chair is enough to work comfortably.

Yes. The electromagnetic technology is CE-certified, non-invasive and works over clothing, without electrodes or gels. That makes the treatment comfortable and safe when used correctly.

Yes, after a short instruction a session can be carried out independently. The practitioner sets the zone and intensity and supervises the first sessions. After that the client can largely repeat the treatment independently within the practice.

A session of about 30 minutes uses roughly 1.3 kWh of electricity, depending on intensity. No gels, electrodes or other consumables are needed. Maintenance is limited to cleaning and an annual technical check.

The X-TONE™ has three main modes: Training mode: targeted muscle strengthening per zone. Pro mode: full control over intensity, frequency and duration for personalised protocols. Recovery mode: rhythmic contractions with a massage-like effect for circulation and relaxation.

For a studio with three modules (Cryo, Light, Oxygen), allow about 20–25 m². The concept is modular, so you can start small and add technologies later.

The Recovery Studio™ usually requires no special permits. All systems are fully electric and free of nitrogen or pressure vessels. We do work with clear protocols and safety guidelines, especially for OxyPro™.

On average a studio is fully operational within 4–6 weeks of the configuration being approved. Delivery, installation and team training are planned as one process.

Yes. We offer various lease and financing options through recognised partners. Together we look at which structure best fits your business case and growth plans.

Every studio implementation includes comprehensive training in using the equipment, client guidance, workflows and basic marketing. On top of that we provide ongoing technical service and support, so your studio stays operational and profitable.